Return to technology applications

One-shot injection, 11 perfluorinated compounds: TQ9100 water quality solution

2026-11-10Environmental Monitoring
Single injection, 11 perfluorinated compounds: TQ9100 water quality solution

GB 5749-2022 includes PFOA and PFOS in routine water quality indicators, while GB/T 5750.8-2023 and HJ 1333-2023 provide detection guidelines for 11 perfluorinated compounds. This article presents a quantitative method developed using the TQ9100 ultra-high-performance liquid chromatography-tandem mass spectrometry system, covering target analyte scope, solid-phase extraction sample preparation and vessel control, chromatographic and mass spectrometric conditions, delayed column usage to avoid system background contamination, and method validation criteria.

Perfluorinated compounds are nearly non-degradable in the environment and persist for long periods in water bodies. GB 5749-2022 has included perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) as routine water quality indicators, with limits of 0.08 μg/L and 0.04 μg/L, respectively; GB/T 5750.8-2023 Section 84.1 provides a liquid chromatography-tandem mass spectrometry method for quantifying 11 perfluorinated compounds in drinking water, requiring a limit of quantification down to 5 ng/L; HJ 1333-2023, an environmental protection industry standard, specifies method detection limits ranging from 0.5 to 0.6 ng/L for PFOS and PFOA in surface water, groundwater, wastewater, and seawater. We established a quantitative method covering these 11 target analytes using the Anyeep TQ9100 ultra-high-performance liquid chromatography-tandem mass spectrometry system.

Target object determines method boundaries

These 11 substances fall into two categories: perfluorocarboxylic acids (PFBA, PFPeA, PFHxA, PFHpA, PFOA, PFNA, PFDA) and perfluorosulfonic acids (PFBS, PFHxS, PFHpS, PFOS), with carbon chain lengths ranging from C4 to C0. Short-chain compounds are highly polar and exhibit weak retention on reverse-phase columns, while long-chain compounds are strongly hydrophobic and tend to adsorb onto tubing and container walls. Balancing both classes within a single gradient presents significant method development challenges.

Sample volume: 1 L, final volume: 1 mL, enrichment factor: 1000-fold. The required limit of quantitation (LOQ) is 5 ng/L per standard, which converts to 5 μg/L in the injection solution. This conversion dictates that both sample preparation recovery and instrument sensitivity must include adequate margins.

Preprocessing:

Measure 1 L of water sample and add 4.625 g ammonium acetate. Adjust pH to between 6.8 and 7.0. Select a weak anion exchange solid-phase extraction (SPE) cartridge with capacity 150 mg/6 mL. Activate sequentially using 5 mL methanol containing 0.1% ammonia, 7 mL methanol, and 10 mL ultrapure water. Maintain the loading flow rate at or below 8 mL/min; excessive flow rates will significantly reduce recovery. After loading, rinse with 5 mL of 25 mmol/L ammonium acetate solution (pH 4) followed by 12 mL of ultrapure water. Apply vacuum until dry. Elute with 5 mL methanol and 7 mL ammonia-methanol mixture. Evaporate the eluate under nitrogen stream in a water bath at 40 °C until near dryness. Finally, bring the volume to 1 mL using 30% methanol-water solution.

Vessel selection is often overlooked more than technique. Use polypropylene or polyethylene for sample vials, graduated cylinders, and centrifuge tubes; avoid glass and PTFE throughout sample preparation, including sampling bottles. If the equipment elevates the blank value, a quantification limit of 5 ng/L becomes meaningless.

Chromatography and Mass Spectrometry Conditions

The column is a C18 column (2.1 × 100 mm, 1.7 μm). Mobile phase A is 5 mmol/L ammonium acetate in water; mobile phase B is methanol. Flow rate: 0.3 mL/min; column temperature: 40 °C; injection volume: 5 μL. The gradient starts with a high aqueous phase to ensure sufficient retention of short-chain carboxylic acids at the column head, followed by an increase in the methanol proportion to elute long-chain components efficiently.

Mass spectrometry in electrospray ionization negative mode with multiple reaction monitoring acquisition.

A critical aspect of PFAS analysis is that the liquid chromatography system itself can release trace amounts of target analytes. We install a C18 delay column in series between the damper and the autosampler to ensure system background elutes after sample peaks, preventing carryover from tubing contamination from skewing results. While this column may seem like an add-on, it ultimately determines the reliability of data at low concentration levels.

Method Validation and Instrument Compatibility

Quantitative analysis was performed using isotope dilution with 13C2-PFHxA, 13C4-PFOA, and 13C4-PFOS as internal standards to cover short-, medium-, and long-chain ranges, correcting for sample preparation losses and matrix effects. Acceptance criteria include: calibration curve correlation coefficient ≥ 0.995; spike recoveries at three concentration levels between 70% and 130%; relative standard deviation ≤ 20%; and inclusion of full-process blanks and duplicates in each batch. Samples requiring re-analysis if internal standard recovery falls below 40% or exceeds 160%.

The TQ9100 architecture directly supports this method. Its ion source features a 90° orthogonal spray design, offering strong resistance to contamination and enabling long-term continuous analysis of aqueous samples. The collision reaction cell employs a 180° curved geometry to eliminate neutral particle interference and suppress crosstalk between adjacent MRM transitions. With 11 analytes and their internal standards analyzed within the same acquisition window, channel isolation and retention time stability determine the reliability of the entire data batch.

苏ICP备18014087号-1